The Bell & Gossett e-1510 1.5BC 15 HP ODP is a base-mounted end suction pump with a 15 HP three-phase ODP motor operating at 3550 RPM. Its 1.5BC casing uses 2.5-inch suction and 1.5-inch discharge connections. The approximate 7.0-inch full-diameter impeller reference supports submittal review for high-pressure booster and industrial water-supply applications.

Open drip proof motor construction must be matched to the installation environment before this high-speed configuration is selected. The nominal impeller diameter, 15 HP motor, and casing size do not define a pump duty. Use the relevant e-1510 curve to confirm required flow, head, suction conditions, system pressure, fluid characteristics, piping resistance, and approved operating requirements.

Key Specifications of the Bell & Gossett e-1510 1.5BC 15 HP ODP Pump

- The 1.5BC casing provides 2.5-inch suction and 1.5-inch discharge connections for matching industrial water-supply piping.
- A 15 HP three-phase motor establishes the listed drive configuration for this high-pressure booster pump arrangement.
- The 3550 RPM two-pole speed defines the supplied high-speed motor reference for hydraulic selection and review.
- Open drip proof construction identifies the ODP motor enclosure specified for this base-mounted pump configuration.
- A nominal approximately 7.0-inch full-diameter impeller requires confirmation against the exact approved pump trim.
- High-pressure booster and industrial water supply are the stated application contexts for evaluating this assembly.

Hydraulic Performance and Application

This Bell & Gossett end suction pump is listed for high-pressure booster and industrial water-supply applications. Its 1.5BC casing, 15 HP motor, 3550 RPM speed, and nominal impeller reference do not establish a duty point. Select through the applicable e-1510 curve and project system design. Verify flow, head, suction conditions, pressure, fluid characteristics, pipe losses, and motor loading before ordering.

Installation and System Requirements

Confirm compatible three-phase electrical service, motor rotation, environmental suitability for the ODP enclosure, and approved system duty before installation. Verify that the 2.5-inch suction and 1.5-inch discharge dimensions fit project piping. Support pipework independently to prevent casing strain. Follow official e-1510 instructions for base mounting, alignment, electrical connection, startup, and checks of the completed pump assembly.

Service and Maintenance Considerations

Verify the approximate 7.0-inch impeller reference against the exact approved trim before selecting replacement components or reviewing hydraulic adjustments. The ODP enclosure requires environmental consideration during planned service. Follow official e-1510 lockout, alignment, seal inspection, and post-service procedures. Do not use nominal impeller diameter as a substitute for exact parts identification, approved curve selection, or documented maintenance requirements.

Why Choose the Bell & Gossett e-1510 1.5BC 15 HP ODP

This arrangement combines a 1.5BC base-mounted casing, 15 HP three-phase ODP motor, 3550 RPM speed, and a nominal 7.0-inch impeller reference. Its 2.5-inch suction and 1.5-inch discharge dimensions provide defined piping checks. Buyers can compare environmental conditions, high-speed motor selection, application context, and required hydraulic duty against the applicable e-1510 pump curve before purchasing.

Warranty and Support

Bell & Gossett commercial pumps carry a 1-Year Limited Warranty against defects in materials and workmanship. Coverage begins at installation and ends no later than eighteen months from shipment, whichever occurs first. Seals, gaskets, elastomers, coatings, and other wear parts are excluded unless sales documentation states otherwise. Mulmotor provides product-information support before purchase and assistance with order-related questions.

Before Ordering the Bell & Gossett e-1510 1.5BC 15 HP ODP Pump

Before ordering, verify that your industrial water-supply or high-pressure booster system requires a 1.5BC casing with 2.5-inch suction and 1.5-inch discharge connections. You should select flow and head using the applicable e-1510 curve, then confirm the 15 HP ODP motor and 3550 RPM speed. Review environmental conditions, impeller trim, pressure requirements, fluid properties, piping support, and service clearance.